Home > To Open > Debian Motion Unable To Open Video Device

Debian Motion Unable To Open Video Device


logged in. 2. Error Logging Utility and Controllers Does "Excuse him." make sense? I set the resolution to 640x360, after a bit of fiddling I found that the height had to be divisible by 16. I am new to python and reasonably good with C programming. have a peek at this web-site

LAN9500 Ethernet 10/100 Adapter Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. Here is what I did: 1. But your correct, it does use quite a lot of CPU on the default. power and i runs fine a while then i get this same error: Code: Select all[1] File of type 1 saved to: /tmp/motion/01-20120629084021-01.jpg
[1] v4l2_next: VIDIOC_QBUF: No such device
[1] Video

Motion Failed To Open Video Device /dev/video0

Any suggestions? Reply Paul Webster says: May 11, 2013 at 10:59 PM There are two ports that you can get responses on. Reply Les Atkins says: May 22, 2013 at 10:28 AM The port is 8081 if you post is not a typo. 8080 is the control port and you should just see Thanks Reply abdulhamid says: April 30, 2014 at 9:02 AM hi all ….

Win7 64 Pro, browser IE 10 Reply Mikeymike says: September 26, 2013 at 12:38 PM I've found that the only browser that works is firefox. This is particularly strange as it doesn't report an error, doesn't start downloading just a new blank tab. I am wrestling with a difficult problem, however. Unable To Open Video Device Raspberry Pi Usb Camera However I notice it occasionally saves a swf file in the tmp folder.

It is plugged into a powered USB hub. Vid_v4lx_start: Failed To Open Video Device /dev/video0: I tried using iframes, but couldn't get it to work in Chrome. another PC or a tablet, and type in the ip address? http://stackoverflow.com/questions/24010510/raspberry-pi-webcam-unable-to-open-video-device What should I do now?

See Cookie Policy for details. Sudo Modprobe Bcm2835-v4l2 In the Chrome browser use "Inspect element." Fine-tuning Configuration Values You can make all kinds of adjustments in your configuration file such as image size, image quality, frame rate, sensitivity to This works on a windows-box with .mp4 files as input (but I haven't been able to make it work on the RasPi): ffmpeg.exe -i c:\temp\outL.mp4 -vf "[in] scale=iw/2:ih/2, pad=2*iw:ih [left] movie=c:\temp\outR.mp4, I have run update and upgrade etc.

Vid_v4lx_start: Failed To Open Video Device /dev/video0:

Reply marc carter says: November 24, 2013 at 10:19 AM This worked a treat. Ubuntu Ubuntu Insights Planet Ubuntu Activity Page Please read before SSO login Advanced Search Forum The Ubuntu Forum Community Ubuntu Official Flavours Support Multimedia Software [SOLVED] Failed to open video device Motion Failed To Open Video Device /dev/video0 Is there any alteration of the instruction where a webcam is not required, only the Rasp Pi camera board? Failed To Open Video Device /dev/video0: No Such File Or Directory Reply murali says: February 19, 2013 at 11:41 AM Hi tom, Thanks for the post.

Not able to access Internet after running sudo chown -R $USER$USER /usr/lib/ Does "Excuse him." make sense? http://netfiscal.com/to-open/dell-unable-to-open-dvd-door.html You signed in with another tab or window. Reply vishal says: August 27, 2013 at 3:44 AM I encountered the same hurdle with "sudo motion start". Then create a .motion directory in your home directory, copy the default configuration file into it, and change ownership to you: ~$ mkdir .motion ~$ sudo cp /etc/motion/motion.conf .motion/ ~$ sudo chown carla:carla Unable To Open Video Device Motion Ubuntu

Thanks for your time.. ------------------------------------------------------------------------------------------- SOLVED!! What could be the problem? jolabpi commented Feb 4, 2016 using ssh from my android phone this is what is returned by MotionEyesOS on running the motion-h command: using motion binary /usr/bin/motion-mrdave jolabpi commented Feb 4, Source My cam's on

Valid range: Camera dependent, default: 352 width 640 # Image height (pixels). Raspberry Pi Camera Device Name Your not trying to start both of these on TCP Port 8081 are you? I had apache2 running on port 80 but stopped that, modified motion.conf to change the port from 8081 to 80 and restarted the motion service.

I dont think it is ...

How can I make it work from boot? It seems the url which MotioEyesOS passes on does not contain the user:password strings as entered in the user password textboxes. Please explain in more detail so that dummies like me can understand it. 2: "You can change other settings but it’s recommend you don’t take more than 2 frames" Do you Device Doesn't Support Vidioc_g_std Reply Tom says: February 2, 2013 at 12:53 PM Strange it should just display a webpage with an image at the top left, does this happen on all computers/browsers?

This is cosole messages: [email protected] /etc/motion $ sudo motion -n [0] Processing thread 0 - config file /etc/motion/motion.conf [0] Motion 3.2.12 Started [0] ffmpeg LIBAVCODEC_BUILD 3482368 LIBAVFORMAT_BUILD 3478785 [0] Thread 1 If I type netstat -lnutp I get: tcp 0 0* LISTEN Connecting to doesnt help either, nor did changing port to 80. Says it cannot connect. have a peek here We need a hub because the camera's draw more power than the Raspberry Pi can actually provide, you see the same with some keyboards and USB dongles.

© Copyright 2017 netfiscal.com. All rights reserved.